Type: Driver
File Name:
File Size: 6.3 MB
30 (4.59)
Downloads: 18
Supported systems: Windows 2008, Windows XP, Windows Vista, Windows 7/8/10
Price: Free* (*Free Registration Required)

Download Now

For more information please visit our Shipping Page. When closing ar-m160 scanner covers, be sure to close the front cover first, then close the side cover.


If closed in a wrong sequence, the covers may be broken. Changing the copy paper size in the tray Note The paper size setting cannot be changed when the machine has stopped temporarily due to running out of paper or a misfeed, or during interrupt copying. During printing even in copy modethe ar-m160 scanner size setting cannot be changed. Do not load ar-m160 scanner that is a different size than the paper size setting. Copying will not be possible.

The currently selected paper feed location indicator will blink and the corresponding paper size ar-m160 scanner is currently set indicator will light steadily. All other indicators will go out. Front guide The front guide is a slide-type guide.

Download and install SHARP SHARP AR-M160 driver

Grasp the locking ar-m160 scanner on the guide and slide the guide to the indicator line of the paper to be loaded. The left guide is an insert-type guide. Remove it and then insert it at the indicator line of the paper to be loaded.

toshiba satellite c660-206Publisher's Description
acer travelmate 3282wxmiProduct Details

When using 11" x 17" sized paper store the left guide in the slot at the left front of the paper ar-m160 scanner. To change the paper size setting of another tray, repeat steps 2 to 3 after pressing the [START] key. The indicator of the selected paper size lights up.

Note Affix the paper size label for the paper size selected in step 3 to the label position on the right end of the tray. Adjustment item list Section A Process section 1 2 3 4 B Mechanism section 1 2 3 4 5 6 7 8 C Image density adjustment 1 Adjustment item Developing doctor gap adjustment MG roller main pole position adjustment Developing bias voltage check Main charger ar-m160 scanner check Image position adjustment Main scanning direction FR direction distortion balance adjustment Main scanning direction FR direction distortion adjustment Sub scanning direction scanning direction distortion adjustment Main scanning direction FR direction magnification ratio adjustment SIM No.


Developing doctor ar-m160 scanner adjustment MG roller main pole position ar-m160 scanner. Copier adjustment A. Process section 1 Developing doctor gap adjustment 1 Loosen the developing doctor fixing screw A. Do not use paper clip, which is too heavy to make a correct adjustment. Put the developing unit horizontally for this adjustment.

Mark the point on the MG roller which is on the extension line from the needle tip. If the distance is not within the ar-m160 scanner range, loosen the fixing screw A of the main pole adjustment plate, and move the adjustment plate in the arrow direction to adjust.

Sharp Ar-m160 / 165

Perform the same procedure for front and the rear frames. If it is within specified range, then fix the doctor ar-m160 scanner screw with screw lock.


Developing doctor gap Both ends 20mm from ar-m160 scanner both ends : 1. Mechanism section Note: If a jam error or paper empty occurs during copying in ar-m160 scanner adjustment by the simulation, the image data are not saved, and therefore recopying is required.

Sharp ARM Supplies and Parts (All)

OC image lead edge position adjustment SIM Note: In advance to this adjustment, the sub scanning ar-m160 scanner ratio adjustment must be performed. The voltage is outputted in the grid bias High output mode during warming up, and in the grid bias Low output mode when warming up is completed.

  • Sharp Ar-m / , Copier Jogeshwari West, Mumbai Unitronix ID:
  • SHARP AR M/ SERVICE MANUAL Image Scanner Exposure (Photography)
  • Sharp Ar-m / , Copier Jogeshwari West, Mumbai Unitronix ID:
  • Download and install SHARP SHARP AR-M160 driver
  • My Account
  • Sharp ARM160 Toner Cartridges

ar-m160 scanner If necessary, perform the following adjustment procedures. The print start position is shifted inside the document edge. Calculate the set value from the formula below. Note: Since the printed copy is used as a test chart, put the scale in paralled with the edge lines. Example: When setting the lead edge void to 2. Note: Before performing the 2nd print surface lead edge position adjustment and the lead edge void adjustment, be sure to perform the 1st print surface lead edge position adjustment in advance, and be sure to perform the 2nd print surface lead edge position adjustment and then the lead edge void adjustment in this sequence. Void amount Standard value: 4mm or less. Side edge void area adjustment SIM Note: Before performing this adjustment, be sure to check that the paper off center adjustment SIM is completed.

The currently set adjustment value is displayed. The correction value is stored and a copy is made. Compare the 2nd copy and the test chart.•Scanning from the operation panel of the machine. •Resolving printer and scanner problems.

•Specifications. ○ Where "AR-XXXX" ar-m160 scanner in this manual. You can download and update all AR-M Scanner drivers for free on this page. Choose a proper version according to your system information and click.

Related Drivers