38DL PLUS WINDOWS 7 X64 DRIVER DOWNLOAD

38DL PLUS DRIVER DETAILS:

Type: Driver
File Name: 38dl_plus_74446.zip
File Size: 22.5 MB
Rating:
4.92
2 (4.92)
Downloads: 2
Supported systems: Windows XP (32/64-bit), Windows Vista, Windows 7, Windows 8.1, Windows 10
Price: Free* (*Free Registration Required)

Download Now
38DL PLUS DRIVER



Memory Card.

38DL PLUS DRIVERS WINDOWS 7

In manufacturing of high-precision components, ultrasonic thickness gaging provides a highly accurate alternative to destructive 38dl plus. The B-Scan will start updating again when the next valid thickness reading is detected. This will be either the Minimum, Maximum, or current thickness depending on the freeze option selected. Min Marker The unit will display both the thickness and the waveform of the held minimum or maximum. During review, the gage will always display the thickness at the Review Marker location.

Refer 38dl plus this document for detailed information on GageView. Opening the instrument might void the warranty. It calls attention to a procedure, practice, or the 38dl plus that if not correctly performed or adhered to will result in death or serious personal injury.

Page Safety For any problem or question regarding this instrument, contact Olympus or an authorized Olympus representative. Legal Entity Type. The EMAT transducer is an effective way to estimate the remaining thickness of steel boiler tubes since you do not have 38dl plus remove the external scale to perform the measurement.

The EMAT transducer creates a nonfocused signal and is designed to give a good estimate of 38dl plus remaining 0. Because of the nonfocused nature of the transducer, it is relatively insensitive to small internal pits. Remove the external oxide and use a standard single or dual element transducer for a more accurate thickness measurement of remaining metal.

38DL PLUS Ultrasonic Thickness Gage

Focused dual element transducers are also more sensitive to any internal pitting. A, June 84 Chapter 6 6. Like for standard transducers, you may need to adjust the gain and the extended blank to make proper thickness measurements. Experienced technicians familiar with the basic theory of ultrasonic gaging and the interpretation of ultrasonic waveforms can also press [WAVE ADJ] to adjust other transducer parameters. The default velocity and zero offset for the ESB EMAT transducer are designed to provide a good estimate of the ferrous metal thickness underneath an 38dl plus oxide scale coating.

To 38dl plus the best accuracy, use calibration samples with external oxide scale made from the material to be tested.

These samples should have 38dl plus metal of known thickness not including external oxide scale and should represent the minimum and maximum thickness of your measurement range. The 38dl plus procedure is the same as for a standard transducer except that you do not need to use couplant to couple the transducer to the material. The EMAT transducer generates shear wave sound energy.

Olympus 38DL PLUS Basic Operation Manual

Consequently, the velocity calculated by the gage is the shear sound velocity of 38dl plus material. A, June Software Options 87 7. You can also purchase software options later. You can activate the software options without having to return the instrument to the factory, by entering an activation code in the 38dl plus see section 7.

38DL PLUS 64BIT DRIVER

Contact your local Olympus representative for more information regarding ordering software 38dl plus. Refer to Table 40 on page for the software option part numbers.

38DL PLUS ADVANCED ULTRASONIC THICKNESS GAGE

A, 38dl plus 88 Chapter 7 7. A single option key can activate one, several, or all software options. To activate a software option 1. Contact your local Olympus representative to purchase one or more software options and provide the alphanumeric serial number. Your Olympus representative will provide you the corresponding option key. A, June Software Options 89 38dl plus. Restart the instrument to complete the activation.

High Temperature Measurements with the 38DL PLUS, 37DL PLUS, MG2XT and MG2DL TechRentals Wiki

These resolutions are adequate for most ultrasonic thickness measurement applications. For single element transducers, the high resolution software option adds the ability to display thickness readings with a high resolution of 0. High 38dl plus is not available for all transducers or measurement screens and is also limited by maximum thickness. Even though the 38DL PLUS has the ability to display thickness readings in high resolution, the measurement accuracy is highly dependent on material, geometry, surface condition, temperature, and needs to be 38dl plus on a case-by-case sample evaluation. High resolution is available for the following transducers and measurement conditions: Single element transducer in the frequency range of 2.

Table 5 on page 90 indicates the transducer to use when using the oxide layer software option. A, June 90 Chapter 7 7.The 38DL PLUS is an innovative instrument that signals a new era in ultrasonic thickness gaging. Ideally suited for almost every ultrasonic thickness application, this handheld thickness gage is fully compatible with a full line of dual and single element transducers. The 38DL PLUS is an innovative instrument that signals a new era in ultrasonic thickness gaging. Ideally suited for almost every ultra- sonic thickness.

Related Drivers